crawford (May rev. 3 Group Page 1 of 95Service Manual Industrial ). crawford (May rev. 3 Group Page 51 of 95 Service Manual Industria). ASSA ABLOY, Crawford, Megadoor and hafa, as words and logos, are examples P. Complete kits. Automation C-kits. Basic control functions. Interlocking.

Author: Negami Nagis
Country: Burma
Language: English (Spanish)
Genre: Environment
Published (Last): 26 January 2014
Pages: 147
PDF File Size: 4.33 Mb
ePub File Size: 8.95 Mb
ISBN: 594-1-26111-901-2
Downloads: 51059
Price: Free* [*Free Regsitration Required]
Uploader: Kilkis

If someone passes the photo cell after, for example,12 sec. Left sideinstallation Always fit the photocell receiver on the left side. C2 photocell safety Photocell module, 2 red w arning Iights Flashing red lights before automatic closing.

These items have become obsolete. When fully open, the time t1 starts to runand when it has run out, t2 starts to run. Transmitter Kwith function buttonsUp – Stop – Down. Unfortunately, we don’t have enough data to generate an accurate Estimate at this time.

Photos and Other Media

Thetime interval t1 applies as per setting on front panel. For latest info see Spare Parts Catalogue. Camber, East Sussex, United Kingdom. Flashing red lights before automatic closing.

crawford Pages 1 – 50 – Text Version | FlipHTML5

Loosen the brace nut of the motor plate. Theswitches are used for sensitivity and for attendance time. This interval is divided into two time intervals t1 and t2.

At automatic closing t2 is replaced by the 2,5 seconds. A AInterlocking normally functions so that one door is blocked X in closed position as soon as the other door is opened. The seller has relisted this item or one 4300p this. An open impulse to theouter door will then be transferred to the inner.


When it indicates that the number of rotations is too low, the door will be stopped and reversed, depending on the position of the door. Works also from reduced open door, safety photocell is then demanded.

Towards the micro switch roller. Read more about the condition. Increase of the sliding force: Email to friends Share on Facebook – opens in a new window or tab Share on Twitter – opens in a new window or tab Share crawfoord Pinterest – opens in a new window or tab Add to Watch list.

All commands except safety are delayed 2,5 seconds while warning lights areflashing. School service boundaries are intended to be used as reference only. Sliding clutch is working – Old type of mechanical units has a brake with the rectifier included.

School data provided by GreatSchools. One board is required for each warning light.

Industrial Door Control Pcb Crawford p Cdm5 Or Cdm6 Control PRICE REDUCED | eBay

Read the Text Version. The time range or sec. X08 Screw terminal for connection of cables to themachinery. To verify enrollment eligibility for a property, contact the school directly.

Exit from parking deck S4 switches set to: Seller assumes all responsibility for this listing. The impulse unit includes all the electronic controlfunctions. The front panel of the board contains diode Lampswhich indicate the current door position.

Only at Warning lights, not at Traffic lights. Crawforrd earlier activation, rotate the nut towards thelimit switch. If no onepasses the photo cell, the door will close after 40sec. There is some amount of infrastructure for biking. This PCB card can be used crwwford e. The electro-motor turns but the door doesnot. Test the doorThe opening and closing time should be min. Motor-protector switch, Main relays.


This can be avoided by using differentfrequencies in the loop systems. If one of the inside toothed wheels is broken ordamaged the complete gear unit has to be replaced. Time for automatic closing without flashing signal, seconds. The bar block shall sit in lower position on L1 forECS This area is very walkable — most errands can be accomplished on foot. The switches of S3 are set on and off.

It will beworthwhile spending a few minutes reading throughthese instructions. Transit is availablewith a few nearby public transportation options. To adjust the limit switches, a control plate can bepressed in and then you can rotate the nuts alongthe screw-thread. The bottom by the RPM control. Back crafword home page Return to top. Email to friends Share on Facebook – opens in a new window or tab Share on Twitter – opens in a new window or tab Share on Pinterest – opens in a new window or tab.