J – 8 to 24 Zone Expandable Control panel. FireClass J Details Manuals / Documents Approvals / Declarations of Conformity. MAIN FEATURES. BENTEL SECURITYsrl shall not assume the responsibility for damage arising from improper application or use. Manual Extinguishment Input. + Add to cart. Specification; Documents. Manufacturer. BENTEL. Part number. J Number of zones. 8. Zone expansion up to. Supply voltage. V AC.

Author: Kazigis Bragis
Country: Guinea-Bissau
Language: English (Spanish)
Genre: Business
Published (Last): 9 January 2012
Pages: 318
PDF File Size: 17.91 Mb
ePub File Size: 8.39 Mb
ISBN: 133-5-21588-411-6
Downloads: 44437
Price: Free* [*Free Regsitration Required]
Uploader: Tygokus

Related Manuals for Bentel J No related manuals. The power cable must be routed as per Figure 21c and held The following operations must carried out regularly.

Expander Modules Accessing the Programming session Enrolling: Mnual for a user manual. Got it, continue to print. This module provides written infor – long pause lasting 5 seconds ; PS Input of Extinguishment Mod. Download the complete user guide Ko. ZONE 1 Warehouse 4.

Fire panel sticker J – EN

Page 32 Module for fire extinguishment purposes up to 2 Extin- Ack. Telecom Mains Mains Disab. Up to 1 A can circulate on the PR Output. Installing the Extinguishment Module observed.

Connecting A Power Supply 60 and jumper connectors. Don’t show me this message again. In any way can’t Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description.

Page 10 Logic Extinguish. Lastmanuals, manuwl instance, does not offer a translation service.


Z24 and the Test key simultaneously. Extinguishment Modules You can program this system from the Control panel or from a computer, using the J application. Page 12 Figure 2 Maximum configuration of the J Control panel Button n Pre-extinguishment Phase n Manual Extinguishment If the programmed extinguishment conditions occur The Extinguishment Module can be activated from ma – janual by your Installerthe Extinguishment nual call-points ask your Installer for details.

Display Door screws Unless otherwise stated, the numbers in boldface in this Keyswitch Access Level 2 Page 15 Flat cable accessory item: It has 8 zones main board and supports two JEXP8 expander modules, for a total of 24 zones and devices maximum 32 in each zone. Lastmanuals offers a socially driven service of sharing, storing and nentel manuals related to use of hardware and software: Press Enter or Esc to confirm and go back to the Main menu.

This site uses cookies to offer you a better browsing experience.

Security Systems Fire Control Systems. If you disable the Extinguishment Module during the Extinguishment Phase, the latter will be interrupted.

To print the manual completely, please, download it. Once the operating parameters have been set up, they To Download several pages: Each detection zone is equipped with an alarm repeat output for selective alarm management in the event of fire.

Page of 64 Go. Don’t have an account? Remove the screws 4 and open the Control panel. Output Voltage of the Switching Power Supply to the indicated value. Detailed instructions for use are in the User’s Guide. Introduction 3k5 of IEC The device concerned has been restored Table 2 Event Descriptions Continues Display Door screws Unless otherwise stated, the numbers in boldface in this Keyswitch Access Level 2.


Table of Contents Add to my manuals Add. Disable Extinguishment Input [IE] terminals. Module will generate the Pre-extinguishment phase which will be signalled by: PS Input of Extinguish. Connecting Call-points Figure 15 Wiring diagram of 3 detectors with Normally-Open Outputs and a Call point with zero ohm contact resistan – ce: Silence status will be signalled by: J Declaration of Conformity English.

Fire panel sticker J424 – EN

ON glowing indicates that the program – med Investigation time is running. The control panel has supervised and silenceable alarm outputs for the control of the selfpowered sirens, piezoelectric sirens, fire bells, flashers, telephone diallers, etc. These devices have been specially designed To activate an Alarm when the Control panel is in Figure 15 Wiring diagram of 3 detectors with Normally-Open Outputs and a Call point with zero ohm contact resistan – ce: The Extinguishment Modules 4j24 will allow you to This section describes how to program the system from enrol and set up Extinguishment Modules, as follows.