ANSI A (), Standard for Accessible and Usable Buildings and Facilities as mandated by law and incorporated by reference by the States and. ICC/ANSI A Accessible and Useable Buildings and Facilities The specifications in this standard make sites facilities buildings and elements. Major changes/additions from ICC ANSI A – found in the edition of A 1. ICC ANSI. A – Section. ICC ANSI A –
|Published (Last):||7 December 2005|
|PDF File Size:||13.89 Mb|
|ePub File Size:||3.20 Mb|
|Price:||Free* [*Free Regsitration Required]|
Reach ranges shall comply with Section A hori- zontal grab bar 24 inches mm mini- back 1a17 m back wall a Without Permanent Seat L.
Fire doors shall have the minimum opening force allowable by the appropriate administrative authority.
The clearance between the car platform sill and the edge of any hoistway landing shall be 1 V 4 inches 32 mm maximum. Other handrails shall comply with Sections The space between the grab bar and projecting objects below and at the ends of the grab bar shall be 1 V 2 inches 38 mm minimum.
Function keys shall comply with Section Vehicle pull-up spaces, access aisles serving them, and a vehicular xnsi from an entrance to the passenger loading zone, and from the 2003 loading zone to a vehicular exit a1117 them, shall provide a vertical clearance of inches mm minimum.
ICC/ANSI A – Accessible and Useable Buildings and Facilities
The telephone and emergency signaling device shall comply with Section Door surfaces within 10 inches mm of the floor, measured vertically, 200 be a smooth surface on xnsi push side extending the full width of the door.
Numeric keys shall be arranged in a key ascending or descending tele- phone keypad layout. The side edge of the seat shall be 1 7 2 inches 38 mm maximum from the back wall of a transfer-type shower and 1 7 2 inches 38 mm maximum from the control wall of a roll-in-type shower.
Objects on multiple posts or pylons where the clear distance between the posts or pylons is greater than 1 2 inches mm amsi have the low- est edge of such object either 27 inches mm maximum or 80 inches mm minimum above the floor.
Characters or braille shall not be located in the pictogram field. Already Subscribed to this document. Ambulatory accessible compartments shall comply with Section Characters shall be V 200 inch 13 mm minimum in height.
The space between the wall and the grab bar shall be 1 V 2 inches 38 mm. For example, it specifies technical requirements for making doors, routes, seating and other elements accessible. Accessible bathtubs shall comply with Section Openings in floor surfaces shall be of a size that does not permit the passage of a V 2 inch 13 mm diameter sphere, except as allowed in Sections Requests for interpretations should be addressed to the secretariat or sponsor whose name appears on the title page of this standard.
Accessible signs shall comply with Section The slope that is perpendicular to the direction of travel see running slope. Extensions are not required for handrails in aisles a1117 seating where the handrails are discontinuous to provide access to seating and to permit crossovers within the aisle.
Individ- ual experts shall have no vote. Stair level identifi- cation signs in tactile characters complying with Section Existing elevators shall not be required to comply with Section Application and Administration Definitions General Site and Building Elements 20 feet min 60 min area to be marked Fig.
Accessible Routes labile Vehicle pull-up spaces, access aisles serving them, and a vehicular route from an entrance to the passenger loading zone, and from the passenger loading zone to a vehicular exit serving them, shall provide a vertical clearance of inches mm minimum. Ramps aansi have landings at bot- tom and top of each ramp run.
Angela Van Etten, J. The clear floor space shall be 48 inches mm minimum in length and 30 inches mm minimum in width. The floor sur- face of the ramp run or ramp landing z117 extend 12 inches mm minimum beyond the inside face of a railing complying with Section Car gates or doors shall be positioned at a narrow end of the clear floor area required by Section Tac- tile characters shall be 2 inches 51 mm mini- wnsi in height.
ANSI A117.1 (2003): Accessible and Usable Buildings and Facilities
Describes a site, building, facility, or portion thereof that complies with this standard. A knee clearance of 24 inches mm minimum above the floor shall be permitted at lavatories and sinks used primarily by children ages 6 through 1 2 where the rim or counter surface is 31 inches mm maximum above the floor.
Communication Elements and Features 65 Figure The visible sig- nal elements shall be 2V 2 inches 64 mm min- imum measured along the vertical centerline Visual and tactile information Tactile information 60 degree typ for equilateral triangle Q Fig. Risers shall be 4 inches 1 00 mm mini- mum and 7 inches mm maximum a17 height.
Table of Contents | ICC/ANSI A – | ICC premiumACCESS
Accessible urinals shall comply with Section Inside handrails on switchback or dogleg stairs or ramps shall be continuous between flights or runs.
A shower seat is not required to be installed in a shower facility for a single occupant, accessed only through a private office and not for common use or public use, provided reinforcement has been installed in walls and located so as to permit the installation of a shower seat complying with Section Shelves shall be 40 inches mm minimum and 48 inches 1 mm maximum above the absi.
The highest operable part of a two-way communication system shall comply with Section A hori- zontal grab bar 24 inches mm mini- mum in length shall be provided on the control end wall beginning near the ansl edge of the bathtub and extend toward the inside corner of the anso. Existing elevator call buttons shall not be required to comply with Section Doorways shall have a clear opening width of 32 inches mm mini- mum.